L-BFGS optimization parameters. Call lbfgs_parameter_init() function to initialize parameters to the default values.
在文件 lbfgs.h 第 175 行定义.
Delta for convergence test. This parameter determines the minimum rate of decrease of the objective function. The library stops iterations when the following condition is met: (f' - f) / f < delta, where f' is the objective value of past iterations ago, and f is the objective value of the current iteration. The default value is 0.
在文件 lbfgs.h 第 215 行定义.
Epsilon for convergence test. This parameter determines the accuracy with which the solution is to be found. A minimization terminates when ||g|| < epsilon * max(1, ||x||), where ||.|| denotes the Euclidean (L2) norm. The default value is 1e-5.
在文件 lbfgs.h 第 194 行定义.
A parameter to control the accuracy of the line search routine. The default value is 1e-4. This parameter should be greater than zero and smaller than 0.5.
在文件 lbfgs.h 第 264 行定义.
A parameter to control the accuracy of the line search routine. The default value is 0.9. If the function and gradient evaluations are inexpensive with respect to the cost of the iteration (which is sometimes the case when solving very large problems) it may be advantageous to set this parameter to a small value. A typical small value is 0.1. This parameter shuold be greater than the ftol parameter (1e-4) and smaller than 1.0.
在文件 lbfgs.h 第 287 行定义.
The line search algorithm. This parameter specifies a line search algorithm to be used by the L-BFGS routine.
在文件 lbfgs.h 第 232 行定义.
The number of corrections to approximate the inverse hessian matrix. The L-BFGS routine stores the computation results of previous m iterations to approximate the inverse hessian matrix of the current iteration. This parameter controls the size of the limited memories (corrections). The default value is 6. Values less than 3 are not recommended. Large values will result in excessive computing time.
在文件 lbfgs.h 第 184 行定义.
The maximum number of iterations. The lbfgs() function terminates an optimization process with LBFGSERR_MAXIMUMITERATION status code when the iteration count exceedes this parameter. Setting this parameter to zero continues an optimization process until a convergence or error. The default value is 0.
在文件 lbfgs.h 第 225 行定义.
The maximum number of trials for the line search. This parameter controls the number of function and gradients evaluations per iteration for the line search routine. The default value is 20.
在文件 lbfgs.h 第 239 行定义.
The maximum step of the line search. The default value is 1e+20. This value need not be modified unless the exponents are too large for the machine being used, or unless the problem is extremely badly scaled (in which case the exponents should be increased).
在文件 lbfgs.h 第 257 行定义.
The minimum step of the line search routine. The default value is 1e-20. This value need not be modified unless the exponents are too large for the machine being used, or unless the problem is extremely badly scaled (in which case the exponents should be increased).
在文件 lbfgs.h 第 248 行定义.
Coeefficient for the L1 norm of variables. This parameter should be set to zero for standard minimization problems. Setting this parameter to a positive value activates Orthant-Wise Limited-memory Quasi-Newton (OWL-QN) method, which minimizes the objective function F(x) combined with the L1 norm |x| of the variables, {F(x) + C |x|}. This parameter is the coeefficient for the |x|, i.e., C. As the L1 norm |x| is not differentiable at zero, the library modifies function and gradient evaluations from a client program suitably; a client program thus have only to return the function value F(x) and gradients G(x) as usual. The default value is zero.
在文件 lbfgs.h 第 311 行定义.
End index for computing L1 norm of the variables. This parameter is valid only for OWL-QN method (i.e., orthantwise_c != 0). This parameter e (0 < e <= N) specifies the index number at which the library stops computing the L1 norm of the variables x,
在文件 lbfgs.h 第 334 行定义.
Start index for computing L1 norm of the variables. This parameter is valid only for OWL-QN method (i.e., orthantwise_c != 0). This parameter b (0 <= b < N) specifies the index number from which the library computes the L1 norm of the variables x, |x| := |x_{b}| + |x_{b+1}| + ... + |x_{N}| . In other words, variables x_1, ..., x_{b-1} are not used for computing the L1 norm. Setting b (0 < b < N), one can protect variables, x_1, ..., x_{b-1} (e.g., a bias term of logistic regression) from being regularized. The default value is zero.
在文件 lbfgs.h 第 325 行定义.
Distance for delta-based convergence test. This parameter determines the distance, in iterations, to compute the rate of decrease of the objective function. If the value of this parameter is zero, the library does not perform the delta-based convergence test. The default value is 0.
在文件 lbfgs.h 第 203 行定义.
A coefficient for the Wolfe condition. This parameter is valid only when the backtracking line-search algorithm is used with the Wolfe condition, LBFGS_LINESEARCH_BACKTRACKING_STRONG_WOLFE or LBFGS_LINESEARCH_BACKTRACKING_WOLFE . The default value is 0.9. This parameter should be greater the ftol parameter and smaller than 1.0.
在文件 lbfgs.h 第 275 行定义.
The machine precision for floating-point values. This parameter must be a positive value set by a client program to estimate the machine precision. The line search routine will terminate with the status code (LBFGSERR_ROUNDING_ERROR) if the relative width of the interval of uncertainty is less than this parameter.
在文件 lbfgs.h 第 296 行定义.
该结构体的文档由以下文件生成:
